Is it ok to change just one brake rotor?

About a year ago getting my tires changed the mechanic mentioned I need new pads. Sure enough they started to grind soon after. I changed all four front pads. Now less then a year later the grinding is back (was always just on the driver's side). I drive easy, no hard braking or drifting around corners. Is it ok to just change the one rotor? How about the pads? The sales guy also was trying to sell a bunch of extras like cleaner to get the oil off the rotor, replacement grease for the caliper bolts and something else because of the time of year (salt). The rotor box says %26quot;ready to install%26quot;, so do I also really need all that other stuff?

In case it matters: 2002 Saturn SL2 front wheel drive %26lt;100K milesIs it ok to change just one brake rotor?
Its fine to do if your broke and only one is giving u the problem but chances are the other isn't far behind. I think your problem is either worn calliper or wheel baring because the problem is only on the 1 side. As for what the sales guy was trying to sell you pretty well bull other than its a good idea to keep the rotor as clean as possible and to keep your calliper bolts or any bolt u might have to take off again with anti seize.



Hope u find this helpfulIs it ok to change just one brake rotor?
That %26quot;sales guy%26quot; does NOT sound good to me! Run (don't walk) to the door and say goodbye forever. Make sure to try another independent repair shop you might find by searching the below link. That new garage will remove both your rotors (easy to do) and simply turn them done on a lathe and charge you about $30 plus the cost of the new pads for a total cost of $125. Do the complete front brake job the right way, and you'll pay less and be safer driving in the long run.



http://www.iatn.net/shopfinder/Is it ok to change just one brake rotor?
Even though it says ready to install, they do ship them with a light oil, and I always spray new rotors down with brake cleaner. As far as replacing one rotor, I would rather not. In hard braking it could cause the car to swerve slightly.Is it ok to change just one brake rotor?
1 get 2nd opinion

2 id rather you get 2 rotors if you can afford it but if poor one is ok ..

3 i can't believe the ****** is trying to nickle and dime you...charge for a smear of grease? and a spray of cleaner PLEASE punch him for me!Is it ok to change just one brake rotor?
if it did it the 2nd time then it,s probably the caliper sticking. you can change just 1 side unless the other rotor is thin then you need to change both rotors to get good braking action. also when you buy rotors the factory puts grease or oil on them to keep them from rusting so before installing them wash them down with brake cleaner.Is it ok to change just one brake rotor?
clean all oil off the rotors and grease the bolts to make sure the calipers slide back in forth freely if they dont you will eat brake pad up.Is it ok to change just one brake rotor?
i would rather change %26quot;both%26quot; rotors at the same time. and if you plan to replace the brake pads, change both too.

the grinding sound that you feel is probably the cause of a warped rotor... this happens when the rotor gets hot when driving then a splash of water hits the rotor or going straight to the car wash after a long drive.

you don't have to buy those brake cleaners or grease.

the rotors are not that expensive anyway and even the brake pads. the expensive one is the %26quot;brake caliper%26quot;... but i don't think that you have a problem with this part.Is it ok to change just one brake rotor?
If you're wearing out one side prematurely, there's a reason. You may have a stuck caliper. The caliper must be free to slide side-to-side on the guide pins as the pads wear. If it's sticking, then you'll likely wear out one pad on that side before the others.If the rotor on the other side still has plenty of metal thickness left, then you could just replace one side. BUT you should have the old rotor ground or machined to remove any 'glaze'- that's when the surface gets polished from wear and heat. If you don't remove the glaze the new rotor will grab better than the old one and cause it to pull to one side. You MUST replace ALL the pads at the same time.

You need to clean and lubricate the guide pins (high-quality bearing grease works fine) and the holes where they slide. There's a small rubber seal that keeps out dirt. If the rubber is broken, dirt and water can get in and cause the caliper to stick. Also, you need to use shims behind the pads and pad silencer goop on the shims. Otherwise you'll end up with brakes that squeal.

be considered abandonment

code for hi5